Discussion on four methods commonly used for anilox roller cleaning

The anilox roller is used to transfer ink through the net point, and the net point is very small. In the process of use, it is easily blocked by the solidified ink, thus affecting the ink transfer effect. Therefore, the anilox roller with the best processing quality will be provided. Do not pay attention to cleaning can not print good prints. At present, the anilox roller cleaning methods are as follows.

1, manual cleaning method

The cleaning agent is applied to the surface of the anilox roller, and the chrome plated metal anilox roller is cleaned with a copper wire brush; while the ceramic anilox roller must be cleaned with a wire brush.

This kind of cleaning method is more convenient and will not cause pollution, but if it is not thoroughly cleaned, the effect of ink transfer will be affected. It is generally suitable for anilox rollers with low cable or not very dirty anilox roller.

2, strong corrosion chemical cleaning method

The corrosive cleaning agent (usually alkaline solution) is evenly applied to the surface of the anilox roller. If necessary, a layer of plastic product is wrapped on the surface of the anilox roller to prevent evaporation of the solution. The anilox roller is ablated for 1 to 48 hours until After the cured ink is sufficiently softened, the anilox roller is cleaned with water or an alcohol solution (acid solution such as acetic acid cannot be used) combined with manual cleaning.

This kind of cleaning method has good cleaning effect, but it has a certain corrosive effect on the anilox roller and will cause environmental pollution.

3, jet cleaning method

The baking soda softening cleaning medium is sprayed onto the surface of the anilox roller, and the solidified ink is crushed to achieve the purpose of cleaning. The baking soda is easy to dissolve, non-toxic, and the crystal body is easy to be broken when colliding with other substances, and will not damage the surface of the anilox roller and the ink cavern wall. Therefore, this cleaning method has a good cleaning effect and has promotion and Use value.

4, ultrasonic cleaning method

The anilox roll is immersed in an ultrasonic cleaning bath filled with a chemical cleaning solution. During the cleaning, the anilox roll rotates slowly. The frequency conversion device in the liquid pool, which can send high-frequency sound waves, starts to work, causing the solution to vibrate to generate bubbles and cause inward explosion. , continuous inward explosive force, the ink out of the network, with the flow of cleaning fluid, cleaning time is generally 15 to 45 minutes.

However, due to long-term vibrations, tiny cracks will appear on the surface of the ceramic anilox roll, and cracks will accumulate. This will allow high pH or crude chemicals to penetrate the porous ceramic coating and gradually corrode the substrate, thus affecting the texture. The life of the roller, therefore, should not be too frequent when cleaning the anilox roller, especially the ceramic anilox roller.

Samina foram offer different Nail Brush like Synthetic Nail Brush and Natural Nail Brush. WHICH BRUSHES FOR WHAT MATERIAL TO CHOOSE CORRECTLY?GEL - for gel modeling we choose brushes suitable for scooping UV / LED gel, so it is necessary to use a flat brush with which you can easily apply UV / LED gel on your nails and shape it into the right shape. There are several hair sizes and types. Furthermore, 2 shapes are used for gel modeling, either flat straight or flat oval. SAMINA Nails offers several types, which you can find HERE.POLY GEL - a special brush is used on the poly gel, which has a spatula at one end to gain mass and a brush at the other end for shaping. We also offer a device that has a silicone tip at the ends, which can be used to shape the poly gel. We offer a poly gel brush HERE.
ACRYLIC - round brushes with a tip are used for modeling acrylic nails. The most common sizes are 8 and 10, and the finest hairs that use liquid are perfectly used for these brushes. We offer these brushes HERE.
NAIL ART - there are a lot of brushes for nail art and decorating. The most important brush that no one should miss is the detailer, or extra thin brush, which is suitable for detailed work around the cuticle and nail walls. You can also paint a French manicure or thin lines with it. It's simply a brush you have to have. Another very popular is, for example, a brush for ombrÃ©, or a gradual transition of colors, for glitter and many others. You can find our offer HERE.

BRUSH CARE
If we want the brush to last us as long as possible, it is also necessary to take good care of it.

Never leave the brush in the water or detergent for too long - the brush head may come loose or the sleeve may start to rust
Clean the brush thoroughly - head and sleeve
Dry the moisture with a clean cloth or napkin
Place the brush upside down to dry
Dry at room temperature

Clean the brushes you use on UVLED gels properly and store them in a dark place. This will prevent direct light from curing the remnants of the gel left on the brush.