[China] wardrobe network to make up for wasted space as a whole furniture and no personality and do construction site wardrobe room and disadvantages of pollution can not move the cabinet after slowly emerged an industry that is customized overall home. Therefore, the process is different from the finished furniture. The process of customizing the wardrobe is simple: door-to-door measurement---out of the design plan---the selected style and color contract in the store---factory order production-- -- Storage inspection --- home installation --- after-sales service.
Customized overall wardrobe sketches, accurate measurements, accurate records, and clear identification, must carefully and accurately measure the size of the customer's room. In the measurement process, the size must not be estimated. Xindi's overall wardrobe is responsible to the customer. It is responsible for itself and the company. The scale personnel must carefully and accurately measure the customer's room. Only accurate measurement can design the appropriate product to make the production. It is more convenient and accurate during the installation process.
1, measuring tools
Tape measure, pen, record sheet, range finder, camera (mobile phone)
2. On-site measurement environment
Observe the basic situation of the site, including beams, columns, anchors, switches, etc.
Plane measurement method:
You can first draw a sketch of the layout with a paper and pen, and then measure the size. The higher the accuracy of the measurement, the better the error is not more than 3mm. It requires accurate measurement. When measuring, record the measured data on the sketch. For example: A1, A2 At A3 and A4, clearly indicate that there must be no missing or unmeasured areas. Multi-point measurement is required for measurement.
Facade measurement method:
You can use the paper and pen to draw the sketch of the vertical layout, and then measure the size. The higher the accuracy of the measurement, the better, the error is not more than 3mm. The measured data is recorded on the sketch when measuring: H1, H2, H3, H4, H5, H6, W1, W2, W3, W4, W5 shall be clearly marked, and there shall be no missing or unmeasured areas. Multi-point measurement shall be used for measurement.
Plane measurement method:
You can use a paper and pen to draw a sketch of the layout, and then measure the size. The higher the accuracy of the measurement, the better the error is not more than 3mm. It requires accurate measurement. When measuring, record the measured data on the sketch. For example: W1, W2 W3, D1, D2 are clearly marked, there must be no missing or unmeasured areas, and multi-point measurement method is required for measurement. Elevation diagram, side view measurement method, ibid.
Sliding door hole size measurement method:
The dimensions of the sliding door opening should be accurate plus or minus 2mm. Only the correct size can produce the sliding door of the right size, in order to make the production more correct, the installation is more convenient, and avoid unnecessary loss. The door hole size measurement method is shown in the figure. The multi-point measurement method such as height H1, H2, H3, width W1, W2 is used to measure the accurate sliding door hole size.
Sliding door size measurement method:
H height does not include the thickness of the top and bottom rail pads, W width does not include the thickness of the left and right side panels, and H height W width is the inner space size and the door hole size. Non-cabinet sliding doors or cabinet sliding doors are required, and multi-point measurement is used to measure the exact size.
Method for measuring the size of the door and swing door:
As shown in Figure H, at W, D, to measure the exact height and width of the total height and width of 2mm, there must be no missing or no test area, (such as single order door) must measure the accurate cabinet size, cover the door, open the door Unlike the sliding door measurement size, the door opening size must not be reported by sliding door.
The on-site measurement is generally two times. The initial test is usually about one week after the decoration company enters the construction site. The purpose is to propose the installation position of the wardrobe or the cloakroom and how to solve the problems such as the plaster line or the kick line with the construction party. Good communication, to avoid discovering problems in the later stage, so that they can't make up for it, which makes the decoration regret.
Lunch Bag
Jilin Y.F. Imp & Exp Co., Ltd is an exporter and manufacturer (Cang nan Y.F. Stationery & Gift Co., Ltd.)in Creative products, such as Backpack ,Shoulder Bag,Pencil Case, Handbag,Multifunctional Bag. Coin Purse .Cosmetic Bag.Storage bags. File Holder.Canvas handbag and Notebook etc. which is a professional stationery company setting research and development, producing, sales and trade into one. Our company always takes quality, service, efficiency and innovation as our management philosophy. Since our brand Y.F. has been put on the market, the products sell well throughout the country consistently, and be exported to Europe and America,, and South America countries as well as regions, where the product enjoys great customer loyalty and good population. Choose Y.F. is not to choose a batch of stationery, but to choose a commitment and responsibility, Thanks for your attention, support, trust an cooperation. Wish to establish long-term business relationship with you in the near future.
Nylon Wash Lunch,Washed Cotton And Linen Lunch Bag,Lunch Bag,Insulation Bag
Jilin Y.F. Import & Export Co.,Ltd , https://www.jlpencilcase.com